CYCLONE SEPARATOR MAKE :CREATIVE LAB MODEL NO:CLMO-13, GYRATORY SIEVE SHAKER MAKE : CREATIVE LAB MODEL NO:CLMO-11, ROTAP SIEVE SHAKER MAKE : CREATIVE LAB MODEL NO:-CLMO-10, TROMMEL VARIABLE SPEED MAKE MODEL:CLMO-09, VIBRATION SCREEN, manufacturers suppliers in India

VIBRATION SCREEN

DESCRIPTION:

Vibrating screens are those, which rapidly vibrated with small amplitude, are less likely to blind than gyrating screens. The vibrations may be generated mechanically or electrically. Mechanical vibrations are usually transmitted from high-speed eccentrics to the casing of the unit and from there to inclined screens. The setup consists of three different screens with 380mm width and 600mm length fitted on a rigid M.S. frame, feed hopper, eccentric etc. Three screens of different sizes are fitted one above the other. The drives are given from an electric motor.

EXPERIMENTATION:

Demonstration of Vibrating Screen

UTILITY REQUIRED

Raw Material for Feed.

Electric Supply: Single phase, 220 V AC, 0.5 kW.

Floor Area 1.5 m x 1 m.

Weighing Balance.

TECHNICAL DETAIL

Vibrating Screen (3 Nos.) Width 400mm, Length 600mm.

Mesh Size - 12.7mm, 9.5mm and 6.3mm (Approx.)

Drive Eccentric shaft coupled to motor.

Feed Hopper Compatible Capacity with arrangement to control feed.

Collecting bins 4 Nos. of suitable capacity.

Control panel Comprises of Standard make On/Off switch, Mains Indicator etc.

Instruction Manual An ENGLISH instruction manual will be provided along with the Apparatus

A good quality painted rigid MS Structure is provided to support all the parts.

TROMMEL VARIABLE SPEED MAKE MODEL:CLMO-09

DESCRIPTION :

Trommel or revolving screens consists of a cylindrical screen rotated about its axis. Simple Trommel may be arranged in series with oversize of the first passing to the second Trommel and the oversize of the second passing to the third, etc. They are quite efficient for coarse sizes. The inclination of Trommel varies depending on the nature of material to be processed.The present Trommel is built with screens of different sizes throughout their length, the feed entering at the end of the finest screen. In this way it is possible to collect materials of different size range from a single Trommel.Drive to the central shaft is given through a variable speed motor coupled to reduction gearbox. Drive is provided for conducting the experiment at varying speed. Set-up is complete in all respect with guards, bins and control panel. A special arrangement to change the angle of inclination of the Trommel is made.

EXPERIMENTATION :

Demonstration of Trommel.

To study the effect of changing the angle of inclination and RPM.
TECHNICAL DETAILS :
Trommel : Dia. 200-mm, Length 1000-mm (approx.)
Sieves : 3 Nos. of different mesh size.
Drive : Variable Speed Motor and Drive speed coupled with
reduction gear box.
Feed Hopper : Compatible Capacity.
Collecting bins : 4 Nos. of suitable capacity.
Control panel Comprises of:
RPM Measurement : Non Contact type Proximity sensor with Digital RPM Indicator Standard make On/Off switch, Mains Indicator etc.
Special arrangement for changing the angle of inclination.
ENGLISH instruction manual consisting of experimental procedures, block diagram.
The whole set-up is well designed and arranged on a rigid structure painted with industrial PU Paint.

ROTAP SIEVE SHAKER MAKE : CREATIVE LAB MODEL NO:-CLMO-10

DESCRIPTION:

The rotap sieve shaker reproduces the circular and tapping motion given to test sieves in hand sieving. The uniform, mechanical action ensures accurate and dependable test. Using the regular height 20-cm diameter sieves, one sample can be tested on a series of six sieves of different openings, all with one operation of machine. The Rotap Sieve Shaker is simple and durably constructed and is run by a FHP motor. The machine is easily installed. No special foundation is required. Test Sieves are supplied at extra cost. A time switch from 0 to 60 minutes is provided.

GYRATORY SIEVE SHAKER MAKE : CREATIVE LAB MODEL NO:CLMO-11

DESCRIPTION:

Gyratory type shaker is driven by FHP motor through a reduction gear suitable to carry up to 7 sieves of 15 cm or 20 cm diameter. When clamped the sieve table does not rotate but it is inclined from the vertical axis and the direction of inclination changes progressively in the clockwise direction. In addition to the gyratory motion of the Shaker, there is an upward and downward movement ensuring that each square inch of the sieve is utilized. The whole mechanism runs in an oil bath. Complete with adopter for 20-cm diameter sieves. Suitable for use from 220/230 volts 50 Hz. AC supply. Test Sieves will be supplied at an extra cost. A time switch from 0 to 60 minutes is provided.

CYCLONE SEPARATOR MAKE :CREATIVE LAB MODEL NO:CLMO-13

DESCRIPTION:

A Cyclone Separator is a vertical cylinder with the inlet stream introduced tangentially near the top, giving the suspension a spinning rotation in the cylinder. The centrifugal force acting on the particles tends to throw them radially to the sides of the cylinder as they spiral downward to a conical bottom where they are removed. A collector is fitted at the bottom & the induced draft blower is used to create the air stream. The classified air leaves the cyclone through a pipe extended down into the cyclone & passes through blower delivery side fitted with fine screen cloth bag to avoid dust expansion in the laboratory. The setup consists of I.D. blower connected to discharge side of Cyclone Separator. A flow meter with manometer is provided to measure the flow rate of air. Pressure drop in the Cyclone is measured by water manometer. Solids are collected in the collector fixed at the bottom. The set-up is complete with flow control & by-pass valve.

EXPERIMENTATION:

To study the performance of a given Cyclone.

To study the effect of inlet gas velocity on overall efficiency

UTILITY REQUIRED

Material for Feed.

Electric Supply : Single phase, 220 V AC, 1 kW.

Floor Area 2 m x 1 m.

Weighing Balance.

TECHNICAL DETAIL

Cyclone Separator Material Stainless Steel, Dia 100mm

Solid Discharge Silo. Material Stainless Steel, suitable capacity with discharge control valve.

Blower ID Fan Blower with 1 HP provided motor

Air flow measurement Flow meter with manometer.

Solids Collector Transparent PVC container fixed with Cyclone.

Fine Dust Collector Bag of Nylon cloth fixed on exit of air.

Control panel Comprises of Standard make On/Off switch, Mains Indicator etc.

Instruction Manual An ENGLISH instruction manual will be provided along with the Apparatus

A good quality painted rigid MS Structure is provided to support all the parts.

Prev 1 2 3 4 5 Next

CYCLONE SEPARATOR MAKE :CREATIVE LAB MODEL NO:CLMO-13 GYRATORY SIEVE SHAKER MAKE : CREATIVE LAB MODEL NO:CLMO-11 ROTAP SIEVE SHAKER MAKE : CREATIVE LAB MODEL NO:-CLMO-10 TROMMEL VARIABLE SPEED MAKE MODEL:CLMO-09 VIBRATION SCREEN