SCREW CONVEYOR (VARIABLE SPEED) MAKE : CREATIVE LAB MODEL NO:CLMO-27, BELT CONVEYOR MAKE : CREATIVE LAB MODEL NO:CLMO-26, ROTARY VACUUM FILTER MAKE : CREATIVE LAB MODEL NO:CLMO-23, PLATE & FRAME FILTER PRESS MAKE: CREATIVE LAB MODEL NO:CLMO-22, MINERAL JIG MAKE : CREATIVE LAB MODEL NO:-21, manufacturers suppliers in India

MINERAL JIG MAKE : CREATIVE LAB MODEL NO:-21

DESCRIPTION:

A jig is a mechanical device used for separating materials of different specific gravity by the pulsation of a stream of liquid flowing through a bed of material. The setup consists of plunger operated by crank mechanism connected to motor coupled with reduction gear box. Sump tank with pump is provided for water circulation.

EXPERIMENTATION:

To calculate percentage recovery of small particle.

UTILITY REQUIRED

Electric Supply: Single phase, 220 V AC, 50Hz, 5–15 Amp Combined Socket with earth Connections.

Water Supply and Drain.

Material for Feed.

Floor Area 1.5 m x 1 m.

TECHNICAL DETAIL

Mineral Jig Tank Material Stainless Steel.

Sump Tank Material Stainless Steel, Compatible Capacity.

Water Circulation FHP Pump.

Product Tank Material Stainless Steel, capacity 10 ltrs (approx.), 2Nos.

Control panel Comprises of Standard make On/Off switch, Mains Indicator etc.

Instruction Manual An ENGLISH instruction manual will be provided along with the Apparatus

A good quality painted rigid MS Structure is provided to support all the parts.

PLATE & FRAME FILTER PRESS MAKE: CREATIVE LAB MODEL NO:CLMO-22

DESCRIPTION:

Pressure filters can apply a large pressure differential across the septum to give economically rapid filtration with viscous liquids or fine solids. The most common types of pressure filters are filter press. A filter press contains a set of plates designed to provide a series of chambers or compartments in which solids may collect. The plates are covered with a filter medium such as canvas cloth. Slurry is admitted to each compartment under pressure; liquor passes through the canvas cloth and out a discharge pipe, leaving a wet cake of solids behind. Plates and frames sit horizontally in a metal rack, with cloth covering the face of each plate, and are squeezed tightly together by a screw. Slurry enters at one end of the assembly of plates and frame. It passes through a channel running lengthwise through one corner of assembly. The set up consists of 7 plates and 6 frames. Frames are covered with filter cloth. Feed is fed by gear pump at the top and filtrate collected at the bottom from each plate by operating the cock. After removing Cake, washing and cleaning can be done by water provided by overhead tank. Inlet & outlet pressures are measured by pressure gauges. Rate of filtrate removals is measured by calibrated tank provided.

EXPERIMENTATION:

To study the operation of filter press in the laboratory.

To evaluate specific cake resistance and medium resistance.

Utility required

Electric Supply: Single phase, 220 V AC, 1.5 kW.

Water supply.

Drain.

Slurry required to performing experiment.

Technical detail

No. of frame 6

No. of Plates 7

Size 200 mm x 200 mm.

Material Acrylic

Screw Jack arrangement for tightening and removing of frames easily.

Filter Medium Filter Cloth

Filtrate collection tray Material Stainless Steel, Suitable size.

Slurry Feed tank Material Stainless Steel, Capacity 40 Ltrs.

Slurry Tank Agitator Stainless Steel Impeller with SS Shaft coupled to FHP

Motor and Reduction Gear Box.

Slurry Feed Pump Gear Pump with FHP motor.

Piping system GI and PVC.

Filtration rate measurement Using measuring tank. Material Stainless Steel

Pressure Measurement Bourdon type pressure gauge.

Overhead water tank Material Stainless Steel , Capacity 25 Ltrs.

Control panel Comprises of Standard make On/Off switch, Mains Indicator etc.

Instruction Manual An ENGLISH instruction manual will be provided along with the Apparatus

A good quality painted rigid MS Structure is provided to support all the parts.

ROTARY VACUUM FILTER MAKE : CREATIVE LAB MODEL NO:CLMO-23

DESCRIPTION:

The most common types of continuous vacuum filter is the rotary drum filter. A horizontal drum with a slotted face turns at less than 2 RPM in an agitated slurry trough. A filter medium, such as canvas, covers the face of drum, which is partly submerged in the liquid. Under the slotted cylindrical face of the main drum is a second, smaller drum with a solid surface. Between the two drums are radial partitions dividing the annular space into separate compartments, each connected by an internal pipe to one hole in the rotating plate of the rotary valve Vacuum and air are alternately applied to each compartment as the drum rotates. The set-up consists of stainless steel drum moving in gunmetal brackets and is divided in 6 compartments, covered by a Stainless Steel mesh. A canvas filter is used for filtration. The whole assembly is fitted with a SS trough in which a agitator is provided. To make the unit a self-contained a slurry mixing and feed arrangement, receiver tanks, vacuum pump, control panel are provided.

EXPERIMENTATION:

To study the performance of a Rotary Vacuum Filter.

To study the operation of Rotary Vacuum Filter under vacuum.

To determine the specific cake resistance and medium resistance.

UTILITY REQUIRED

Electric Supply: Single phase, 220 V AC, 1.5 kW.

Water supply.

Drain.

Slurry required to performing experiment.

TECHNICAL DETAIL

Filter Drum Material Stainless Steel, Dia. 250 mm, Length 350 mm.

Mesh Material Stainless Steel

Filter Canvas Cloth

No. of Zones 6 Nos.

Drive for Drum FHP motor coupled to a Reduction Gear Box

Trough Material Stainless Steel, Compatible capacity.

Trough Agitator Material Stainless Steel, driven by FHP motor with Reduction Gearbox.

Slurry Tank Stainless Steel, capacity 75 Ltrs.

Slurry Pump Gear Pump with ½ HP motor

Slurry Tank Agitator Stainless Steel Impeller with SS Shaft coupled to FHP motor and Reduction Gear Box

Filtrate Receiver Material Stainless Steel, Capacity 10 Ltrs. (2 Nos.)

Vacuum Pump Liquid Ring type coupled to a 1 HP Motor

Piping GI and PVC size ½

Control panel Comprises of: Standard make On/Off switch, Mains Indicator etc.

Instruction Manual An ENGLISH instruction manual will be provided along with the Apparatus

A good quality painted rigid MS Structure is provided to support all the parts.

BELT CONVEYOR MAKE : CREATIVE LAB MODEL NO:CLMO-26

DESCRIPTION:

Belt Conveyor as the name suggests, consists of endless belt, suitably supported and driven, which carry or transport solids from place to place. Belts are made of either canvas, reinforced rubber or strip steel etc. Belt conveyors are adapted to wide varieties and quantities of material, require relatively low power, and can transport solid for long distances. The present setup is of lab size moving on two horizontal rollers. The drive is given through a worm reduction gear coupled to a motor. Feed hopper is fitted on one side of conveyor and the other end one collecting tray is placed. It demonstrates the working of belt conveyors as used in the industries. The setup has a special arrangement to change the angle of belt.

EXPERIMENTATION:

To study the working of a Belt Conveyor

To study the effect caused by changing the angle of inclination

UTILITIES REQUIRED

Material for feed

Electric Supply: Single Phase, 220v AC, 1KW

Floor Area: 1mx 1m

TECHNICAL DETAILS

Belt Material Nylon/Synthetic Width: 200mm, Length: 1500mm

Drive for Conveyor ½ HP motor coupled to reduction Gear Box

Bins 2 Nos. Collecting Bin and Distributing Bin

Control Panel comprises of Standard make on/off switch, mains indicator etc.

With Standard make On/Off switch, Mains Indicator etc.

Digital display of temperatures in a multi channel indicator with 0.1c accuracy

Instruction Manual : An ENGLISH instruction manual and block diagram will be provided along with the Apparatus

The whole set-up is well designed and arranged in a good quality painted structure.

SCREW CONVEYOR (VARIABLE SPEED) MAKE : CREATIVE LAB MODEL NO:CLMO-27

DESCRIPTION:

The screw conveyor is one of the oldest and most versatile conveyor types. These are compact, requiring little headroom and no return mechanism. The material is also mixed as it passes through the conveyor. Screw or helical flight conveyors consists of a steel shaft having a spiral or helical fin fastened to the shaft and rotating in a trough without touching the trough, so that the helical fin pushes the material along the trough. It is fitted with a variable speed motor. Drive with a compatible reduction gearbox to run the screw conveyor at variable speed. A RPM indicator with Proximity sensor indicates the RPM of conveyor.
EXPERIMENTATION:

To study the effect of various operating parameters on conveying.

To study the effect caused by changing the angle of inclination.

To study the effect of RPM on efficiency of conveyor.

UTILITY REQUIRED

Material for Feed.

Electric Supply : Single phase, 220 V AC, 1 kW.

Floor Area 1 m x 2 m.

TECHNICAL DETAIL

Trough Material Stainless Steel Length 750mm. (approx.)

Screw Material Stainless Steel Dia 75mm, Length 750mm., Pitch Scale 75mm

Central Shaft for Screw Material Stainless Steel, Length 750mm.

Drive Standard make FHP Motor with Drive coupled to Reduction Gear Box.

Feed Hopper Suitable capacity with feed control arrangement.

Bins 2 Nos. Collecting Bin and Distributing Bin Special arrangement for changing the angle of inclination 0° - 30°.

Control panel Comprises of:

RPM Measurement Digital RPM Indicator, Non Contact type with Proximity sensor. Standard make On/Off switch, Mains Indicator etc.

Instruction Manual An ENGLISH instruction manual will be provided along with the Apparatus

A good quality painted rigid MS Structure is provided to support all the parts.

Prev 1 2 3 4 5 Next

SCREW CONVEYOR (VARIABLE SPEED) MAKE : CREATIVE LAB MODEL NO:CLMO-27 BELT CONVEYOR MAKE : CREATIVE LAB MODEL NO:CLMO-26 ROTARY VACUUM FILTER MAKE : CREATIVE LAB MODEL NO:CLMO-23 PLATE & FRAME FILTER PRESS MAKE: CREATIVE LAB MODEL NO:CLMO-22 MINERAL JIG MAKE : CREATIVE LAB MODEL NO:-21