DIGITAL LEVEL GAUGE FLOW CHANNEL ACCESSORIES, BROAD CRESTED WEIR FLOW CHANNEL ACCESSORIES, KAPLAN TURBINE TEST RIG MAKE :CREATIVE LAB MODEL NO:-CLFM-50, PELTON TURBINE TEST RIG MAKE : CREATIVE LAB MODEL NO:-CLFM:-48, HYDRAULIC RAM TEST RIG MAKE : CREATIVE LAB MODEL NO:CLFM-40, manufacturers suppliers in India

HYDRAULIC RAM TEST RIG MAKE : CREATIVE LAB MODEL NO:CLFM-40

DESCRIPTION:

Hydraulic Ram is used for pumping small quantity of water at high head, when large quantity of water at small head is available. It operates on the principle that if flowing water is suddenly brought to rest in a long pipe, a phenomena known as water hammer occurs, wherein a pressure wave travels along the pipe. This principle is

used in the Hydraulic Ram to pump water. The set-up consists of a box incorporating pulse and non-return valves and a supply reservoir on a stand which is fed by the overhead tank. An air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic.

EXPERIMENTATION:

To find out discharge of useful water and waste water.

To find out the efficiency of the Hydraulic ram.

UTILITIES REQUIRED:

Electricity supply: Single Phase, 220 V AC, 50 Hz, 5-15 amp combined socket with earth connection.

Water Supply (Initial Fill)

Floor Drain required.

Floor Area Required: 1.5 m x 0.75 m

TECHNICAL DETAILS:

Ram : Supply Head 1.0 m, Delivery Head 4 m (Max.)

Water Circulation : FHP Pump, Crompton make.

Sump Tank : Capacity 140 Ltrs. (approx.)

Overhead Tank : Capacity 50 Ltrs. (approx.)

Air Vessel : Suitable Capacity.

Flow Measurement : Using Measuring Tank & Electronic Stop Watch for waste water and for useful water

Pressure Gauge : Bourdon type.

Control Panel Comprises of : Standard make On/Off Switch, Mains Indicator, etc.

Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus Tanks will be made of Stainless Steel.

The whole set-up is well designed and arranged in a good quality painted structure.

PELTON TURBINE TEST RIG MAKE : CREATIVE LAB MODEL NO:-CLFM:-48

DESCRIPTION:

Pelton Wheel Turbine is only impulse water turbine now in common use named in honour of Sir L. A. Pelton (1829-1908) of California, USA. It is a tangential flow impulse turbine. The water strikes the buckets along the tangent of the runner. The energy available at the inlet of the turbine is only kinetic energy. The pressure at the inlet and outlet of the turbine is atmospheric. This turbine is used for high heads. The present set-up consists of a runner. The buckets are mounted on the runner. The water is fed to the turbine, through SS nozzle with a SS spear, by means of Centrifugal Pump, tangentially to the runner. Flow of water into turbine is regulated by adjusting the spear position by the help of a given hand wheel. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is provided with a transparent acrylic sheet for observation of flow on to the buckets. This runner assembly is supported by rigid MS structure. Load is applied to the turbine with the help of this brake dynamometer so that the efficiency of the turbine can be calculated. Pressure gauge is fitted at the inlet of the turbine to measure the total supply head to the turbine.

EXPERIMENTATION:

To study the operation of a Pelton Wheel Turbine.

To determine the Output Power of Pelton Wheel Turbine.

To determine the Turbine Efficiency.

UTILITIES REQUIRED

Water Supply and Drain.

Electricity 5 kW, 440V AC, Three Phases.

Floor Area 1.5 x 0.75 m

TECHNICAL DETAILS:

Output Power: 1 kW.

Discharge: 400 LPM (Approx.)

Supply Head: 25 m

Speed: 1000 RPM (Approx.)

Nozzle: Material Stainless Steel.

Spear: Material Stainless Steel.

Dynamometer: Rope Brake type.

Sump Tank: Capacity 200 Ltrs.

Water Circulation: Centrifugal Pump, Standard make, Capacity 5 HP,

Three Phase, 2800 RPM

Discharge Measurement: Pitot tube with Manometer

Control Panel Comprises of:

L&T make Starter, Mains Indicator, and MCB for overload protection.

Instruction Manual: An ENGLISH instruction manual will be provided along

With the Apparatus Tanks will be made of Stainless Steel.

The whole set-up is well designed and arranged in a good quality painted structur

KAPLAN TURBINE TEST RIG MAKE :CREATIVE LAB MODEL NO:-CLFM-50

DESCRIPTION:

Kaplan Turbine is an axial flow reaction turbine named in honour of Dr. B. Kaplan, a German Engineer. This turbine is suitable for low head. The power produced by a turbine is proportional to QH. As the head (H) decreases the discharge (Q) must increase to produce the same power. The present set-up consists of a scroll casing housing a runner. Water enters the turbine through the stationary guide vanes and passes through the runner axially. The runner has a hub and airfoil vanes, which are mounted on it. The water is fed to the turbine by means of Centrifugal Pump. The runner is directly mounted on one end of a central shaft and other end is connected to a brake arrangement. A transparent hollow cylinder made of acrylic is fitted in between the draught tube and the casing for observation of flow on to the airfoil vanes. This runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of drum brake arrangement so that the efficiency of the turbine can be calculated. The set-up is supplied with control panel. Pressure and Vacuum gauges are fitted at the inlet and outlet of the turbine to measure the total supply head on the turbine.

EXPERIMENTATION:

To study the operation of Kaplan turbine.

To determine the Output Power of Kaplan Turbine.

To determine the turbine efficiency.

UTILITIES REQUIRED :

Electricity Supply: Three phase, 420 VAC, 50 Hz, 32 Amp. 4 Pole MCB with earth connection.

Water supply (Initial Fill)

Floor Drain Required.

Floor Area required: 3.5 x 1.5 m

Tachometer to measure RPM

Mercury for Manometer (250gms)

TECHNICAL DETAILS :

Output Power : 1 kW.

Discharge : 1000 LPM

Supply Head : 5-8 M

Normal Speed : 2000 RPM

Dynamometer : Rope Brake type.

Water Circulation : Centrifugal Pump, CRI/Standard Make, Capacity 5 HP, 3 Phase.

Discharge Measurement : Pitot Tube with Manometer

Sump Tank : Capacity 200 Ltrs.

Pressure Measurement : Pressure Gauge & Vacuum Gauge

Piping & Fittings : Pipes & fittings with flow control valves of suitable size

Control Panel Comprises of:

L&T make Starter, Mains Indicator, MCB for overload protection.

Instruction Manual : An ENGLISH instruction manual will be provided along

with the Apparatus Tanks will be made of Stainless Steel.

The whole set-up is well designed and arranged in a good quality painted structure

BROAD CRESTED WEIR FLOW CHANNEL ACCESSORIES

LEARNING OBJECTIVES:

Free and submerged overfall at the broad-crested weir

Effect of the weir edges on flow processes

Sharp-edged contour

Rounded contour

Together with a level gauge:

Determination of the discharge coefficient

Determination of the discharge

Comparison of the theoretical and the measured discharge

SPECIFICATION

Weir with sharp edges

Additional elements for rounded edges

Weir body with sealing lips

Technical data

Weir body

Material: PVC

Dimensions and weight

LxWxH: 260x96x120mm (weir body) LxWxH: 40x86x120mm (element for rounded edges)

Weight: approx. 5kg

Elements for energy dissipation

LEARNING OBJECTIVES:

Comparison of the effect of different elements for energy dissipation

Chute blocks

Baffle blocks

End sills

Observation of the hydraulic jump with and without end sills respectively baffle blocks

SPECIFICATION

All elements made of PVC

1 weir with chute block, 2 baffle blocks with 5 rectangular blocks, 1 baffle block with 5 triangular blocks, end sills with different height

TECHNICAL DATA

WEIR WITH CHUTE BLOCK

LxWxH: 172x84x160 mm

END SILL

LxWxH: 84x25x25 mm

LxWxH: 84x25x50 mm

BAFFLE BLOCKS

LxWxH: 84x25x25 mm

blocks, WxH: 14x14 mm

Dimensions and weight

LxWxH:1000x84x10 mm (base plate); Total weight: approx. 3kg

DIGITAL LEVEL GAUGE FLOW CHANNEL ACCESSORIES

DESCRIPTION
Measurement of discharge depths with probe tip or hook, both vertically travelling, carrier for level gauge can be placed upon and fixed to any position of the experimental section

FEATURES

Accessory for measuring water levels

SPECIFICATION

Device for measuring discharge depths in the experimental flume

Measurement either with probe tip or hook

Vertically travelling probe tip or hook

Digital display to indicate the discharge depth

Use of corrosion resistant materials

TECHNICAL DATA

Scale: - measuring range: 0...300 mm; graduation: 0.01mm; Max. travel: 300 mm

LxWxH: 150x120x380 mm; Weight: approx. 2kg

Prev 1 2 3 4 5 6 Next

DIGITAL LEVEL GAUGE FLOW CHANNEL ACCESSORIES BROAD CRESTED WEIR FLOW CHANNEL ACCESSORIES KAPLAN TURBINE TEST RIG MAKE :CREATIVE LAB MODEL NO:-CLFM-50 PELTON TURBINE TEST RIG MAKE : CREATIVE LAB MODEL NO:-CLFM:-48 HYDRAULIC RAM TEST RIG MAKE : CREATIVE LAB MODEL NO:CLFM-40