logo
 
left right
shadow
PLATE TYPE HEAT EXCHANGER MAKE :CREATIVE LAB MODEL NO:CLHT-13
DESCRIPTION:
Plate types Heat Exchanger are popular in process industries because they occupy less space and offer reasonable temperature drop. Valves are provided to control the flow rates of hot and cold water. Flow rates of hot and cold water are measured using Rotameters. A magnetic drive pump is used to circulate the hot water from a re-cycled type water tank, which is fitted with heater and Digital Temperature Controller.
EXPERIMENTATION:
The main object of the experimental setup is to study the following at various flow rates:
LMTD
Heat transfer rate
Overall Heat Transfer Co-efficient.
UTILITIES REQUIRED
Water supply 20 lit/min (approx.) and drain.
Electricity Supply: 1 Phase, 220 V AC, 4 kW.
Floor area of 1.5 m x 0.75 m.
TECHNICAL DETAILS
System Water to Water
Plates Material stainless steel
Frame Rigid MS Structure
Water Flow Measurement Rota meters (2Nos.) one each for cold & hot fluid.
Hot Water Tank Made of Stainless steel Insulated with ceramic fibre wool.
Hot Water Circulation Magnetic Pump
Heater Nichrome wire heater.
Control panel comprising of:
Digital Temp. Controller 0-199.90C, (For Hot Water Tank)
Digital Temp. Indicator 0-199.90C, with multi-channel switch
Temperature sensors RTD PT-100 type.
With Standard make On/Off switch, Mains Indicator etc.
Instruction Manual : An ENGLISH instruction manual will be provided along with the                     Apparatus
A good quality painted rigid MS Structure is provided to support all the parts.
 
 

HELICAL COIL HEAT EXCHANGER MAKE : CREATIVE LAB MODEL NO: CLHT-15
DESCRIPTION:
The apparatus consists of fabricated shell, inside which coil tubes on outer side are fitted. The present set up is a heat exchanger, with cold water flows through shell. Valves are provided to control the flow rates of hot and cold water. Flow rates of hot and cold water are measured using Rotameters. A magnetic drive pump is used to circulate the hot water from a re-cycled type water tank, which is fitted with heaters and Digital Temperature Controller.
EXPERIMENTATION:
The main object of the experimental setup is to study the following at various flow rates: 
 LMTD 
 Heat transfer rate 
 Overall Heat Transfer Co-efficient.
UTILITIES REQUIRED
Electricity Supply: 1 Phase, 220 V AC, 50 Hz, 32 amp MCB with earth connection (Earth voltage Would be less than 5 volts) 
Water supply: 5 lit/min (approx.) 
Floor Drain. 
Floor area: 1.5 m x 0.75 m.
TECHNICAL DETAILS
System : Water to Water. 
 Shell. : Material Stainless steel. 
Insulated with ceramic wool and cladded with aluminum foil. 
Dia. 220 mm,
Length 500 mm (Approx.) 
Tube : ID 13 mm, 
OD 16mm approx., 
Coil Type Water 
 Flow Measurement : Rotameters (2Nos.) one each for cold & hot fluid. 
 Hot Water Tank : Made of Stainless steel Insulated with ceramic fibre wool. 
Hot Water Circulation : Magnetic Pump 
Heaters : Nichrome wire heater (2 Nos.) 
Control panel comprising of: Digital Temp. 
Controller : PID Controller, 0-199.9°C, (For Hot Water Tank)
Digital Temp. Indicator : 0-199.9°C, with multi-channel switch 
Temperature sensors : RTD PT-100 type. With Standard make On/Off switch, Mains Indicator  etc. 
An ENGLISH instruction manual consisting of experimental procedures, block diagram etc.  will be  provided along with the Apparatus
 

THERMAL CONDUCTIVITY OF LIQUIDS MAKE :CREATIVE LAB MODEL NO:CLHT-20
DESCRIPTION:
The apparatus is designed to determine thermal conductivity of different liquids. The apparatus consists of a heater. The heater heats a thin layer of liquid. A cooling plate removes heat through liquid layer, ensuring unidirectional heat flow. Temperature is measured across the liquid layer and complete assembly is properly insulated. A proper arrangement for changing the liquids is provided. The whole assembly is kept in a chamber.
EXPERIMENTATION:
Determination of thermal conductivity of liquid.
Study of variation of thermal conductivity of liquid with temperature.
UTILITIES REQUIRED:
Water supply 5 lit/min (approx.)
Drain.
Electricity Supply: 1 Phase, 220 V AC, 2 Amp.
Table for set-up support.
TECHNICAL DETAILS:
Liquid Chamber Dia 160 mm (approx.).
 Heater Dia 100 mm sandwiched between copper plates.
Insulation Ceramic Wool
Cooling chamber Made of Aluminium for water circulation.
Control panel comprising of :
Digital Voltmeter 0-300 Volt.
Digital Ammeter 0-2 Amp.
Variac 0-230 V, 2 Amp.
Digital Temp. Indicator 0-199.90C, with multi-channel switch
Temperature Sensors  RTD PT-100 type.
With standard make On/Off switch, Mains Indicator etc.
Instruction Manual An ENGLISH instruction manual will be provided along with the Apparatus
Valves are provided for drain, charging & overflow line to make system flexible.
MS Cabinet to accommodate the slab assembly.
 

THERMAL CONDUCTIVITY OF INSULATING POWDER MAKE : CREATIVE LAB MODEL NO:CLHT-18


THERMAL CONDUCTIVITY OF INSULATING SLAB MAKE : CREATIVE LAB MODEL NO:CLHT-19
DESCRIPTION:
The set-up is designed to determine thermal conductivity of insulating materials in the form of slab. The apparatus consists of main central heater and ring guard heater, sandwiched between the specimens.  Cooling plates are provided on either side of the specimen. Two identical specimens are clamped between a heater that ensures unidirectional heat flow through specimen. The whole assembly is kept in chamber and insulated by ceramic wool insulation around the set-up.
EXPERIMENTATION:
Determination of thermal conductivity of insulating material in the form of slab.
Study of variation of thermal conductivity of the material with temperature.
UTILITIES REQUIRED:
Water supply 5 lit/min (approx.)
Drain.
Electricity Supply: 1 Phase, 220 V AC, 2 Amp.
Table for set-up support.
TECHNICAL DETAILS:
Specimen
Diameter180 mm (approx).
Thickness 12 mm (approx).
Central Heater Dia 100 mm sandwiched between copper plates.
Ring Guard Heater Width 35 mm sandwiched between copper rings.
Cooling chamber Made of Aluminium for water circulation. 2 Nos.
Insulation Ceramic wool
 Control panel comprising of     :
Digital Voltmeter 0-300 Volt. (Nutronics Makes)
Digital Ammeter 0-2 Amp (Nutronics Makes)
Variac 0-230 V, 2 Amps, (2 Nos.)
One each for central & ring guard heater.
Digital Temp. Indicator 0199.90C, with multi-channel switch (Nutronics Makes)
Temperature Sensors RTD PT-100 type.(6 Nos)
With standard make on off switch, Mains Indicator etc.
The whole setup is mounted on a powder coated base plate
 

Prev   1  2  3  4  5   Next
THERMAL CONDUCTIVITY OF INSULATING SLAB MAKE : CREATIVE LAB MODEL NO:CLHT-19    THERMAL CONDUCTIVITY OF INSULATING POWDER MAKE : CREATIVE LAB MODEL NO:CLHT-18    THERMAL CONDUCTIVITY OF LIQUIDS MAKE :CREATIVE LAB MODEL NO:CLHT-20    HELICAL COIL HEAT EXCHANGER MAKE : CREATIVE LAB MODEL NO: CLHT-15    PLATE TYPE HEAT EXCHANGER MAKE :CREATIVE LAB MODEL NO:CLHT-13    
Categories
 CHEMICAL REACTION ENGINEERING LAB
 CIVIL ENGINEERING LAB
 CIVIL LAB EQUIPMENTS
 CORE LAB
 ELECTRICAL ENGINEERNG LAB EQUIPMENTS
 ELECTRONICS ENGINEERING LAB EQUIPMENTS
 ELECTRONICS LAB
     ADVANCED COMMUNICATION LAB
 ENVIRONMENT LAB
 FLUID MACHINERY LAB
 FLUID MECHANICS LAB
 HEAT TRANSFER LAB
 HYDRAULIC BENCH & ACCESSORIES
 MASS TRANSFER LAB
 MATERIAL TESTING LAB
 MECHANICAL OPERATION LAB
 MEDICAL LAB EQUIPMENTS
     ANALYTICAL LAB EQUIPMENT
 METALLURGICAL & MATERIAL SCIENCE LAB
 MOMENTUM TRANSFER LAB
 MONENTUM TRANSFER LAB
 PETROLEUM TESTING LAB
 PHYSICS LAB
 PROCESS CONTROL & INSTRUMENTATION LAB
 PRODUCTION LAB
 REFRIGERATION & AIR CONDITIONING LAB
 STRENGHT OF MATERIAL LAB
 STRUCTURE LAB
 SURVEY LAB
 THEORY OF MACHINE LAB
 THERMODYNAMICS LAB
 WORKSHOP
 
Follow us on
facebook twitter in  
 
bottom
 
Home About us Products Enquiry Contact us