HAMMER MILL MAKE : CREATIVE LAB MODEL NO:CLMO-06, MUD BALANCE , SOIL HYDROMETER , ROD MILL MAKE : CREATIVE LAB MODEL NO:CLMO-05, BALL MILL VARIABLE SPEED MAKE : CREATIVE LAB MODEL NO:CLMO-03, manufacturers suppliers in India

BALL MILL VARIABLE SPEED MAKE : CREATIVE LAB MODEL NO:CLMO-03

DESCRIPTION:

Ball Mills are horizontal rotating cylindrical steel chamber of half filled with steel balls. The size reduction is accomplished by the impact of balls as they fall back after being lifted by the baffles fitted in the rotating chamber. Ball Mill is fitted on a sturdy MS frame. Charging of balls and material is done by the means of opening provided in the chamber. The chamber is turning about the horizontal axis through a reduction gearbox drive through a ½ HP variable speed motor. Drive is provided to vary the RPM. A RPM indicator with proximity switch is provided in the set-up. A revolution counter is provided to find out the number of turns. Special arrangement is done to free the Ball Mill from reduction gearbox for charging and discharging the material.

EXPERIMENTATION:

To study effect of RPM on the power consumption of a Ball Mill.

To determine the efficiency of a Ball Mill for grinding a material of known Wi.

UTILITY REQUIRED

Raw Material for Feed.

Electric Supply : Single phase, 220 V AC, 1 kW.

Set of Sieves with Sieve Shaker for analysis.

Floor area 1.5 x 1m

TECHNICAL DETAIL

Ball Mill Material MS Dia 275mm, Length 350mm. Thickness 5 mm.

Discharge Chute Suitable size.

Feed Size 6 mm (approx.)

Product Size 200 mesh (approx.)

Drive ½ HP, variable speed motor and Drive, coupled to Reduction Gearbox.

Product receiver Material Stainless Steel of suitable size.

Revolution Counter Mechanical type.

Control Panel Comprises of

Energy measurement Electronic Energy meter

RPM Measurement Digital RPM Indicator, Non Contact type with Proximity sensor.

Instruction Manual An ENGLISH instruction manual will be provided along with the Apparatus

The set-up is fitted with required guards.

The whole set-up is well designed and arranged in a good quality painted structure.

ROD MILL MAKE : CREATIVE LAB MODEL NO:CLMO-05

DESCRIPTION:

Rod Mills are horizontal rotating cylindrical steel chamber of half filled with steel rods of length slightly less than the length of chamber. The rods are of different diameter. The size reduction is accomplished by the impact of rods as they fall back after being lifted by the rotating chamber. Rod Mill is fitted on a sturdy MS frame. Charging of rods and material is done by the means of opening provided in the chamber. The chamber is turning about the horizontal axis through a reduction gearbox drive through a ½ HP motor. The stepped pulley arrangement is done for moving the Rod Mill at three different speeds. A revolution counter is provided to find out the number of turns. Special arrangement is done to free the Rod Mill from reduction gearbox for charging and discharging the material.

EXPERIMENTATION:

To study effect of RPM on the power consumption of a Rod Mill.

To determine the efficiency of a Rod Mill for grinding a material of known Wi.

UTILITY REQUIRED:

Raw Material for Feed.

Electric Supply: Single phase, 220 V AC, 1 kW.

Set of Sieves with Sieve Shaker for analysis.

Floor area 1.5 x 1m

TECHNICAL DETAIL:

Rod Mill Material MS

Dia 275mm, Length 350mm. Thickness 5 mm.

Discharge Chute Suitable size.

Drive ½ HP motor coupled to Reduction Gearbox & 3 step pulley to get 40, 50 and 60 RPM (Approx.)

Revolution Counter Mechanical type.

Product receiver Material Stainless Steel of suitable size.

Control Panel Comprises of

Energy Measurement Electronic Energy meter.

MCB For overload protection.

Standard make on/off switch, Mains Indicator etc.

Instruction Manual An ENGLISH instruction manual will be provided along with the Apparatus

The set-up is fitted with required guards.

The whole set-up is well designed and arranged in a good quality painted structure.

SOIL HYDROMETER

Description:

Soil Hydrometer is ssed for grain size analysis of soils where more than 10% of the material will pass through 75 microns I.S. sieve.

Manufactured from clear transparent glass having uniform clarity throughout the upper end on which density scale is engraved.

The scale range is 0.0995 to 1.030 density (gms/cc) at 270C. Smallest division on the scale is 0.0005.

MUD BALANCE

Description:

Mud balance is designed to find out specific gravities of Semi Liquids like mud and other liquids. Mud Balance is a simple method for fast and accurate determination of density of the drilling mud.

Specification:

• It has a Stainless Steel bam calibrated specific gravities from 0.8 to 2.5.

• A stainless steel cup with lid and overflow vent is fitted on one side of the beam.

• A counter weight with cursor slides over the graduated scale.

• The beam has a knife edge at centre which rests in fulcrum fitted in the stand.

• Leveling screws and spirit level are fitted dot the stand.

HAMMER MILL MAKE : CREATIVE LAB MODEL NO:CLMO-06

DESCRIPTION :

Hammer mill consists of Pivoted hammers, mounted on a horizontal shaft. Crushing takes place by impact between the hammers and anvil plate. The hammers delivers heavy blows to the feed material while it is in suspension, driving it against an anvil plate until it is fine enough to pass through the opening of the mesh fitted in the bottom of the Mill.The present Hammer Mill has sturdy housing that contains 4 Nos. of T shaped hammers, pivoted to a disc, which is fitted with the shaft of the mill turning about the horizontal axis. The shaft is directly coupled to a motor. The housing contains a semi-circular teethed liner (or anvil plate) on the top of it. A glass window to see through in the Mill is fixed on the front cover, which can be opened to change the sieve. Different mesh sizes are provided to get different product size. A hopper with feed opening and adjustment is provided in the Mill. The crushed material is collected in a receiver provided in the set-up. This mill can accept a feed size of 6.5mm or less.

EXPERIMENTATION:

To study the operation of a Hammer Mill.

UTILITIES REQUIRED :

Raw Material for Feed.

Electric Supply : 3 Phase, 440 V AC, 2 kW.

Set of Sieves with Sieve Shaker for analysis.

Floor area 0.5 x 0.5m

TECHNICAL DETAILS

Hammer Mill Housing

Material Stainless Steel, Dia 145mm, Depth 75mm

Feed Size 6mm approx.

Product Size 60 - 150 mesh approx.

Hammers Material Stainless Steel, Anvil Plate Size 55mm x 15mm Material Stainless Steel, Teethed Semi-circular Hopper Material Stainless Steel with discharge control arrangement Discharge Chute Suitable size Drive2 HP Crompton motor (Three Phase) Product Receiver Material Stainless Steel of suitable size Starter2 HP Crompton make

Prev 89 90 91 92 93 94 95 96 Next

HAMMER MILL MAKE : CREATIVE LAB MODEL NO:CLMO-06 MUD BALANCE SOIL HYDROMETER ROD MILL MAKE : CREATIVE LAB MODEL NO:CLMO-05 BALL MILL VARIABLE SPEED MAKE : CREATIVE LAB MODEL NO:CLMO-03